[Aug 03, 2026] 100% Latest Most updated NACE-CIP2-001 Questions and Answers
Try with 100% Real Exam Questions and Answers
NEW QUESTION # 45
You are the NACE Coating Inspector on a tank lining project and are asked to perform a high voltage holiday test after the coating applicators have completed their final repairs. After meeting all the confined space entry permit you enter the tank and notice a very strong odor of solvent.
Your first course of action should to:
- A. Don your air supplied respirator and continue the testing
- B. Exit the tank and document the incident in your daily report
- C. Investigate to find the source of the odor
- D. Exit the tank and immediately and report the problem to the nearest safety supervisor
Answer: D
NEW QUESTION # 46
Centrifugal blast cleaning requires:
- A. A large volume of air to propel the abrasive
- B. The use of single use abrasives
- C. Well maintained blast wheels
- D. Very large nozzles
Answer: C
NEW QUESTION # 47
When NACE/SSPC WJ 1 is referenced; what type of equipment would the Inspector expect to see on the job:
- A. Abrasive Blasting Equipment
- B. Scarifiers
- C. Power Tools
- D. Water Jetting Equipment
Answer: D
NEW QUESTION # 48
You are the NACE Level 2 Coating Inspector where SSPC PA 2 has been specified with an additional requirement that no individual gauge reading shall be below a certain value.
As this is not part of the standard you should:
- A. Call your supervisor
- B. Ignore the additional requirement
- C. Enforce the additional requirement
- D. Request clarification from the specifier
Answer: C
NEW QUESTION # 49
You are the NACE Level 2 Inspector with the final responsibility to prepare the final report for a very large structural steel shop project which has gone very well. It is due next week. The work has been ongoing for two years and several NACE Level 1 Inspectors have worked under your supervision throughout the project. You find you are missing one week of daily reports for the night shift from the very beginning of the project and despite your best efforts they are cannot found.
You FIRST preferred course of action is to:
- A. Use creative writing to cover over the fact they are missing
- B. Do not complete your report until they can be found
- C. Plainly state in your report that they are missing
- D. Re-create the reports as not much was going on during night shift anyway
Answer: C
NEW QUESTION # 50
You have just your NACE CIP Level 2 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:
- A. Review the NACE Attestation prior to making a decision
- B. Accept assignment without hesitation
- C. Meet with the prospective employer to scope of your role
- D. Advise the prospective employer that you cannot accept the position
Answer: A
NEW QUESTION # 51
Coating surveys may include which steps?
Select All That Apply:
- A. Develop a survey plan
- B. Summarize the collected data
- C. Schedule the remedial work
- D. Evaluate the coatings performance
Answer: A,B,C,D
NEW QUESTION # 52
When observing fabrication defects the NACE Inspector should:
- A. Write an NCR and call the fabricator
- B. Require they be corrected prior to coating
- C. Stop the job immediately
- D. Consult the specification to determine how they should be treated
Answer: D
NEW QUESTION # 53
Linings are used on the interior of pipelines to
- A. afford limited temperature insulation.
- B. provide protection against soil chemicals.
- C. reduce magnetic polarity.
- D. protect the transported product.
Answer: D
NEW QUESTION # 54
Application of Thermal Spray Coatings requires:
- A. No particular skills
- B. The same skills as welding
- C. The same skills as liquid coatings
- D. Specialized skills supported by training and experience
Answer: D
NEW QUESTION # 55
When working with someone who is very concerned about Stability and maintaining adherence to the status-quo, the Inspector should try to:
- A. Make sure they are the center of attention in all site meetings
- B. Implement immediate to get them motivated
- C. Challenge their value to the team and try to get them out of their comfort zone
- D. Give them as much advance notice as possible about upcoming changes
Answer: D
NEW QUESTION # 56
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. Fusion Bonded Epoxy
- B. 2-Layer Polyethylene (PE)
- C. 3-Layer Polyethylene (PE)
- D. Coal Tar Enamel
Answer: C
NEW QUESTION # 57
Coating application to concrete substrates is:
- A. Not required as Concrete is inorganic
- B. The same as coating steel
- C. Less challenging, than coating steel
- D. More challenging than coating steel
Answer: D
NEW QUESTION # 58
Differences in technique for abrasive blasting concrete versus steel require the operator to:
- A. Increase the standoff distance
- B. Move the nozzle quicker
- C. a), b) and c)
- D. Lower the blast pressure
Answer: C
NEW QUESTION # 59
When ASIN D 3363 is specified the Inspector must:
- A. Record the highest value attained
- B. Record the two end points identified in the standard
- C. Record the percentage of failure
- D. Use the correct solvent
Answer: B
NEW QUESTION # 60
The solvent sensitivity/solvent wipe test (ASTM D4752) is used to determine the cure of
- A. inorganic zincs.
- B. urethanes.
- C. epoxies.
- D. powder coatings.
Answer: A
NEW QUESTION # 61
When completing the Final Inspection report the Inspector should write the report using:
- A. Language that only technical experts would understand
- B. Language that another NACE Inspector would understand
- C. Language that only in the project would understand
- D. Language that the most would understand
Answer: D
NEW QUESTION # 62
Which surface preparation method uses a dilute acid solution to remove laitance and I roughen the concrete surface?
- A. Acid etching
- B. High-pressure water washing
- C. Sacking
- D. Stoning
Answer: A
NEW QUESTION # 63
Which standards are generally established by private-sector bodies and are available for use by any person or Organization, private or government?
- A. Mandatory
- B. De facto
- C. Voluntary
- D. Consensus
Answer: C
NEW QUESTION # 64
Which is used to calibrate a pH meter?
- A. Standard solvent solution
- B. Deionized water
- C. Standard buffer solution
- D. Distilled water
Answer: C
NEW QUESTION # 65
It is always possible to see moisture on a steel substrate:
- A. False
- B. True
Answer: A
NEW QUESTION # 66
Cold-applied tape
- A. have a cross-linked polyethylene backing and a heat-activated adhesive.
- B. is polyethylene film, heat laminated, 'With an adhesive layer of butyl glue.
- C. is typically green or led and looks like "painted" finish.
- D. are identifiable by its distinct colors, usually light blue, green, Or Grey.
Answer: B
NEW QUESTION # 67
Coating Surveys are legally required:
- A. On commercial marine vessels and offshore platforms
- B. On high pressure gas lines and fireproofed structures
- C. On food and beverage vessels and can linings
- D. On water tanks and potable water pipelines
Answer: A
NEW QUESTION # 68
......
Achieving the NACE-CIP2-001 certification demonstrates that an individual has the knowledge and skills required to inspect coatings and ensure that they meet the required standards for quality and performance. Coating Inspector Level 2 certification is recognized by industry professionals and is highly valued by employers. It can lead to career advancement opportunities and increased earning potential for individuals in the coatings industry.
New NACE NACE-CIP2-001 Dumps & Questions: https://simplilearn.lead1pass.com/NACE/NACE-CIP2-001-practice-exam-dumps.html